A little help for the road ahead.Free to browse, with no sign-up

RV error codes

Atwood RV water heater and furnace error codes.

We list 10 Atwood codes from the maker’s own manuals. Find yours to see what it means, what you can safely check, and when to call a tech. Need a tech now?

If you smell propane, see smoke, or a CO alarm goes off, turn it off, get everyone out, and call 911.

Atwood water heaters (electronic ignition)

Where the code shows: Electronic ignition models have no coded display. An indicator light on the remote wall switch shows a lockout.

To reset: Turn the switch off for at least 30 seconds, then turn it back on.

Indicator light on

Lockout from high water temperature

Atwood and Dometic electronic ignition water heaters

The heater shut down because the water got too hot. The light on your remote switch comes on to tell you.

What you can check

  • Wait for the water to cool.
  • Turn the switch off for at least 30 seconds, then turn it on again.

When to call a tech

If the lockout comes back, call a tech. The manual says to contact a service center. Find a mobile tech near you

From Dometic (Atwood) Water Heater Model 4, 6, 10 Operation Manual (MPD 93756), Electronic ignition operation, step 5.

Light stays on over 15 seconds

Burner did not light

Atwood and Dometic electronic ignition water heaters

The switch light stayed on after you turned the heater on. That means the burner did not light.

If you smell propane, leave the RV, shut the tank valve and call your gas supplier or 911.

What you can check

  • Make sure the propane tank valve is open and the tank has gas.
  • Turn the switch off and wait 5 minutes. Then turn it on again.

When to call a tech

If the light still stays on, call a tech. The ignition or gas supply may need service. Find a mobile tech near you

From Dometic (Atwood) Water Heater Model 4, 6, 10 Operation Manual (MPD 93756), Electronic ignition operation, step 2.

Atwood Hydro Flame furnaces

Where the code shows: A small light on the control board inside the furnace flashes a pattern, pauses 3 seconds, and repeats. The board is behind a cover, so a tech usually reads it. If you can see the light without taking anything off, count the flashes.

To reset: For a hard lockout, reset the thermostat or turn the power switch off, then back on.

LED steady on

Control board problem

Atwood Hydro Flame 8500-IV furnaces (8516, 8520, 8525, 8531, 8535)

The LED stays lit and does not flash. The ignition control board has a fault.

What you can check

  • Turn the furnace power switch off, wait, then turn it on again.

When to call a tech

If the LED stays on after a reset, call a tech. The control board may need to be replaced. Find a mobile tech near you

From Hydro Flame 8500-IV Series Furnace Models 8516, 8520, 8525, 8531, 8535 Technical Installation Manual (MPD 33179), Diagnostic chart.

1 flash

Limit switch or airflow problem

Atwood Hydro Flame 8500-IV furnaces (8516, 8520, 8525, 8531, 8535)

The LED flashes once, then pauses 3 seconds. The furnace is too hot or air is not moving well.

What you can check

  • Turn the thermostat down and let the furnace cool, then try again.

When to call a tech

If the 1 flash comes back, call a tech. The limit switch or the airflow may need service. Find a mobile tech near you

From Hydro Flame 8500-IV Series Furnace Models 8516, 8520, 8525, 8531, 8535 Technical Installation Manual (MPD 33179), Diagnostic chart.

2 flashes

Flame sense problem

Atwood Hydro Flame 8500-IV furnaces (8516, 8520, 8525, 8531, 8535)

The LED flashes twice, then pauses 3 seconds. The furnace cannot sense the flame.

If you smell propane, leave the RV, shut the tank valve and call your gas supplier or 911.

What you can check

  • Make sure the propane tank valve is open and the tank has gas.
  • Reset the thermostat or turn the power switch off, then on.

When to call a tech

If the 2 flashes come back, call a tech. The flame sensor or gas supply may need service. Find a mobile tech near you

From Hydro Flame 8500-IV Series Furnace Models 8516, 8520, 8525, 8531, 8535 Technical Installation Manual (MPD 33179), Diagnostic chart.

3 flashes

Ignition lockout

Atwood Hydro Flame 8500-IV furnaces (8516, 8520, 8525, 8531, 8535)

The LED flashes three times, then pauses 3 seconds. The furnace tried to light and could not.

If you smell propane, leave the RV, shut the tank valve and call your gas supplier or 911.

What you can check

  • Make sure the propane tank valve is open and the tank has gas.
  • Reset the thermostat or turn the power switch off, then on. Do not keep cycling the thermostat more than three times.

When to call a tech

If it will not light after a reset, call a tech. The igniter, gas valve or gas supply may need service. Find a mobile tech near you

From Hydro Flame 8500-IV Series Furnace Models 8516, 8520, 8525, 8531, 8535 Technical Installation Manual (MPD 33179), Diagnostic chart.

LED steady on

Control board problem

Atwood Hydro Flame AFM series furnaces (AFMD16, AFMD20, AFMD25, AFMD30, AFMD35)

The LED stays lit and does not flash. The ignition control board has a fault. This is a hard lockout.

What you can check

  • Turn the furnace power switch off, wait, then turn it on again.

When to call a tech

If the LED stays on after a reset, call a tech. The control board may need to be replaced. Find a mobile tech near you

From Hydro Flame AFM Series Furnaces Models AFMD16 to AFMD35 Technical Installation Manual (Literature 32471), Ignition control diagnostic codes chart.

1 flash

Limit switch or airflow problem

Atwood Hydro Flame AFM series furnaces (AFMD16, AFMD20, AFMD25, AFMD30, AFMD35)

The LED flashes once, then pauses 3 seconds. The furnace is too hot or air is not moving well. This is a soft lockout, so the furnace may try again on its own.

What you can check

  • Turn the thermostat down and let the furnace cool, then try again.

When to call a tech

If the 1 flash comes back, call a tech. The limit switch or the airflow may need service. Find a mobile tech near you

From Hydro Flame AFM Series Furnaces Models AFMD16 to AFMD35 Technical Installation Manual (Literature 32471), Ignition control diagnostic codes chart.

2 flashes

Flame sense problem

Atwood Hydro Flame AFM series furnaces (AFMD16, AFMD20, AFMD25, AFMD30, AFMD35)

The LED flashes twice, then pauses 3 seconds. The furnace cannot sense the flame. This is a hard lockout. Reset the thermostat or power.

If you smell propane, leave the RV, shut the tank valve and call your gas supplier or 911.

What you can check

  • Make sure the propane tank valve is open and the tank has gas.
  • Reset the thermostat or turn the power switch off, then on.

When to call a tech

If the 2 flashes come back, call a tech. The flame sensor or gas supply may need service. Find a mobile tech near you

From Hydro Flame AFM Series Furnaces Models AFMD16 to AFMD35 Technical Installation Manual (Literature 32471), Ignition control diagnostic codes chart.

3 flashes

Ignition lockout

Atwood Hydro Flame AFM series furnaces (AFMD16, AFMD20, AFMD25, AFMD30, AFMD35)

The LED flashes three times, then pauses 3 seconds. The furnace tried to light and could not. It is a soft lockout and tries again after 1 hour.

If you smell propane, leave the RV, shut the tank valve and call your gas supplier or 911.

What you can check

  • Make sure the propane tank valve is open and the tank has gas.
  • Reset the thermostat or turn the power switch off, then on. Do not keep cycling the thermostat more than three times.

When to call a tech

If it will not light after a reset, call a tech. The igniter, gas valve or gas supply may need service. Find a mobile tech near you

From Hydro Flame AFM Series Furnaces Models AFMD16 to AFMD35 Technical Installation Manual (Literature 32471), Ignition control diagnostic codes chart.

Questions people ask.

What does Atwood code Indicator light on mean?

The heater shut down because the water got too hot. The light on your remote switch comes on to tell you. If the lockout comes back, call a tech. The manual says to contact a service center.

What does Atwood code Light stays on over 15 seconds mean?

The switch light stayed on after you turned the heater on. That means the burner did not light. If the light still stays on, call a tech. The ignition or gas supply may need service.

What does Atwood code LED steady on mean?

The LED stays lit and does not flash. The ignition control board has a fault. If the LED stays on after a reset, call a tech. The control board may need to be replaced.

What does Atwood code 1 flash mean?

The LED flashes once, then pauses 3 seconds. The furnace is too hot or air is not moving well. If the 1 flash comes back, call a tech. The limit switch or the airflow may need service.

Where these codes come from.

We read each Atwood manual below and wrote the codes in plain words. If your manual says something different, follow your manual.

Other brands: Norcold · Lippert · Onan · Truma · Furrion · Dometic · Suburban · Search all codes

RV Repair Connect is not part of Atwood. Brand names belong to their owners.