Lippert Ground Control leveling (3.0 and TT) Where the code shows: On the touch pad screen as words, or on the OneControl panel or app as a message; the touch pad light blinks red.
To reset: Fix the cause, then press ENTER on the touch pad. On Rev. B pads, press Retract All to clear most faults.
Excess Angle Excessive Angle Feature Disabled Low Voltage Out Of Stroke External Sensor Jack Time Out Auto Level Fail Comm Error Bad Calibration Internal Sensor Function Aborted Hall Effect Short LF Jack RF Jack LM Jack RM Jack LR Jack RR Jack Low Voltage Excessive Angle External Sensor Tongue Jack LF Jack RF Jack LR Jack RR Jack BAD CALIBRATION AUTO LEVEL FAIL HALL POWER SHORT LOW VOLTAGE EXCESS ANGLE FUNCTION ABORTED JACK TIME OUT EXTERNAL SENSOR OUT OF STROKE EXCESSIVE ANGLE FEATURE DISABLED Left-Front Jack Fault Right-Rear Jack Fault Blinking red LED Solid red LED
The RV tipped too far during auto level. The controller may not be held down well. The ground may be too sloped.
What you can check Make sure the controller is held down firmly. Move your RV to flatter ground and try again. When to call a tech If the code keeps coming back on flat ground, call a tech. The controller or its sensor may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
The RV tipped too far during auto level. The controller may not be held down well. The ground may be too sloped.
What you can check Make sure the controller is held down firmly. Move your RV to flatter ground and try again. When to call a tech If the code keeps coming back on flat ground, call a tech. The controller or its sensor may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
The system can not do what you asked yet. Your touch pad may need a power cycle, or the zero point may not be set.
What you can check Turn the touch pad off and back on. Set the front landing gear to hitch height first, if you asked for hitch recognition. When to call a tech If the zero point will not set, call a tech. The leveling sensor may need checking. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
Your RV battery got too weak while the jacks ran. A weak battery or a bad connection can cause this.
What you can check Charge the 12-volt battery. When to call a tech If the battery is fine and the code stays, call a tech. A wire or connection may be bad. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
A jack ran out of travel and could not lift more. Or a jack stalled with a high amp load.
What you can check Look at where the jacks are sitting. Move your RV to flatter ground. When to call a tech If a jack still stalls, call a tech. The jack may be bent or damaged. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
The controller lost its link to the rear sensor. A wire or plug may be bad.
When to call a tech Call a tech. The connection to the rear sensor needs repair. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
Auto level took longer than it should. Something may be slowing a jack.
What you can check Look at where the jacks are sitting. When to call a tech If it happens again, call a tech to check the jacks. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
Auto level could not finish. The ground may be too uneven, or the zero point may be set wrong.
What you can check Look at where the jacks are sitting. Move your RV to flatter ground. When to call a tech If it still fails on level ground, call a tech to reset the zero point. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
The controller and the touch pad stopped talking. A wire or plug may be loose or hurt.
When to call a tech Call a tech. The harness may need a check or a new part. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
The level sensor readings are out of range.
When to call a tech Call a tech. The manual says the controller needs to be replaced. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
There is a problem with the sensor inside the controller.
When to call a tech Call a tech. The manual says the controller needs to be replaced. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
A button was pressed while auto level was running, so it stopped.
What you can check Start auto level again. Do not press any button until it ends. When to call a tech If it stops on its own with no button press, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
A short was found in a jack sensor circuit.
When to call a tech Call a tech. They can test for the short and fix it. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Touch Pad Error Codes.
The left front jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. Extend them first if needed. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Special Jack Error Codes.
The right front jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. Extend them first if needed. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Special Jack Error Codes.
The left middle jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. Extend them first if needed. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Special Jack Error Codes.
The right middle jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. Extend them first if needed. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Special Jack Error Codes.
The left rear jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. Extend them first if needed. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Special Jack Error Codes.
The right rear jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. Extend them first if needed. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point or 6 Point Owner's Manual (Rev. 11.19.18, CCD-0001518) , Special Jack Error Codes.
Your RV battery got too weak while the jacks ran.
What you can check Charge the 12-volt battery. When to call a tech If the code stays after charging, call a tech. A wire or connection may be bad. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Touch Pad Error Codes.
You moved the RV too far out of level by hand. The code clears by itself when you move the jacks back.
What you can check Run the jacks back toward level. You do not need to press ENTER. When to call a tech If it comes back with small moves, call a tech to check the sensor. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Touch Pad Error Codes.
The controller lost its link to the leveling sensor.
When to call a tech Call a tech. The sensor connection needs repair. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Touch Pad Error Codes.
The tongue jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Special Leveling Jack Error Codes.
The left front jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Special Leveling Jack Error Codes.
The right front jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Special Leveling Jack Error Codes.
The left rear jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Special Leveling Jack Error Codes.
The right rear jack has a problem with its sensor signal or its wire to the motor.
What you can check Check that the 12-volt battery is charged. Press and hold the retract button to home the jacks. Each jack must be able to retract at least 6 inches. When to call a tech If the code comes back, call a tech. A harness, plug or fuse may need service. Find a mobile tech near you
From Ground Control TT Leveling System Owner's Manual (Rev. 02.28.19, CCD-0001756) , Special Leveling Jack Error Codes.
The zero point was not set the right way.
What you can check Set the zero point again. When to call a tech If it will not clear, call a tech. Note: this fault can not be cleared from the touch pad, only from the panel or app. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
Auto level could not finish. The controller may be loose, or the battery voltage dropped.
What you can check Make sure the controller is held down firmly. Charge the 12-volt battery. When to call a tech If it keeps failing, call a tech to test the battery under load and the controller. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
A short was found on a jack sensor power line.
When to call a tech Call a tech to check the jack harness. You can clear this fault only from the OneControl panel or app. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
The battery is weak, or a wire or connection is bad.
What you can check Charge the 12-volt battery. When to call a tech If the code stays after charging, call a tech to test the battery and wiring. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
The controller may be loose, or the site may be sloped.
What you can check Make sure the controller is held down firmly. Move your RV to flatter ground. When to call a tech If it comes back on flat ground, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
Someone stopped auto level while it ran.
What you can check Press OK, then start the sequence again. When to call a tech If it stops without a button press, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
The system could not level in the time it expects.
What you can check Look at where the jacks are sitting. When to call a tech If it happens again, call a tech to check the jacks. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
The link to the rear sensor is bad.
When to call a tech Call a tech to repair the sensor connection. This fault can not be cleared from the touch pad. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
The controller may be loose, or the site may be sloped.
What you can check Make sure the controller is held down firmly. Move your RV to flatter ground. When to call a tech If it comes back on flat ground, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
You moved the RV too far out of level by hand. It clears by itself.
What you can check Move the jacks back toward level. You do not need to press OK. When to call a tech If it keeps showing with small moves, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
You asked for hitch recognition, but no hitch height is set. Or the zero point is not set.
What you can check Run an AUTO LEVEL to set the hitch height. When to call a tech If the zero point will not set, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , OneControl Touch Panel or OneControl App Error Codes.
The left front jack has a sensor or wire problem.
What you can check Check that the 12-volt battery is charged. Press ENTER to auto retract and home the jacks. When to call a tech If the fault returns, call a tech to check the harness and fuses. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , Special Jack Error Codes.
The right rear jack has a sensor or wire problem.
What you can check Check that the 12-volt battery is charged. Press ENTER to auto retract and home the jacks. When to call a tech If the fault returns, call a tech to check the harness and fuses. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , Special Jack Error Codes.
The touch pad has an error. The panel or app shows which one.
What you can check Look at the OneControl panel or app to see the error. Press Retract All to clear most common faults (Rev. B). When to call a tech If the error returns after you clear it, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , Red/Green LED Indicator on Auto Leveling Control Touch Pad.
The battery is low.
What you can check Charge the 12-volt battery. When to call a tech If the light stays red after charging, call a tech. Find a mobile tech near you
From Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel Owner's Manual (Rev. 06.28.18, CCD-0001519) , Red/Green LED Indicator on Auto Leveling Control Touch Pad.
Lippert In-Wall (Schwintek) slide-outs Where the code shows: By LEDs on the controller board. Green blinks show motor 1 or 2. Red blinks (2 to 9) show the code.
To reset: Push the slide extend or retract switch to reset the board, then push it again to run the slide.
2 red blinks 3 red blinks 4 red blinks 5 red blinks 6 red blinks 8 red blinks 9 red blinks
The battery got so low that it dropped below 6 volts while the slide moved. In one manual, a short in the switch wire can also cause it.
What you can check Charge the 12-volt battery. When to call a tech If the battery is good and it comes back, call a tech. The battery wires or switch wire may be bad. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.
The battery was below 8 volts when you started the slide.
What you can check Charge the 12-volt battery. The manual suggests under 11 volts is too low. When to call a tech If it comes back with a charged battery, call a tech. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.
The battery voltage is too high, over 18 volts.
When to call a tech Call a tech. A charger or the RV power system may be at fault. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.
The motor pulled too much power. Something may be blocking the slide.
What you can check Look outside and inside for things in the way, like a tree, a post, luggage or furniture. Clear anything in the way and try again. When to call a tech If nothing is in the way, call a tech. A motor or gear may be stuck. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.
The motor, or a wire to the motor, has shorted.
What you can check Check the 12-volt fuses. Replace a blown fuse. When to call a tech Call a tech. If a new fuse blows right away, a wire to the board has a problem. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.
The controller gets no signal from the motor encoder. This is the most common code. It is often a wire problem or a bad motor.
What you can check Check the 12-volt fuses. Make sure nothing is blocking the slide. When to call a tech Call a tech. A wire may be pinched or broken, or a motor may be loose or bad. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.
The power wire to the motor encoder has shorted to ground. This is usually a wire problem.
When to call a tech Call a tech to check the wires. Find a mobile tech near you
From In-Wall Slide-Out Troubleshooting (Rev. 09.09.20) , Troubleshooting, Error Codes.